If you have a garage door that’s not closing, it’s important to find out why. Otherwise, you’re leaving your home vulnerable to intrusion. There are several reasons why your garage door might not be closing, but the most common one is that the sensors are dirty. The sensors are what tell the door when to stop and go, so if they’re covered in dirt or cobwebs, they won’t work properly. Another reason could be that the tracks are misaligned. It may be because the photo eye sensors are out of alignment.
A lot of people experience issues with their garage door when they use it. Usually, there are early indications that prevent further problems from occurring. If the garage door won’t go, it usually requires one or more of the reasons listed below.
Photo eye sensors are what your garage door uses to sense when the door is open or closed. If they’re dirty, they may not be able to properly read the status of the door. Most sensors are located on the top section of your garage door and are protected by a plastic cover. The photo eyes are located on either side of the garage door, about six inches off the ground. They send an infrared beam across the opening of the door, and if that beam is interrupted, it prevents the door from closing. Check to see if there is anything blocking the path of the beams, such as dirt, cobwebs, or leaves.
Faulty tracks and rollers can also cause your garage doors to stop closing or opening. Something in the tracks may also be the reason behind the problem, and bent tracks may also contribute to your doors not working. In the event the rollers also do not function correctly, this may possibly be to blame. Lubricating the rollers can help fix this problem.
If you have a two-car garage, you may be able to open the other side of your garage door. This is helpful because it allows you to see if the tracks are lined up properly and if there is any debris on the tracks that could be causing your door to malfunction.
A mechanism that drives the garage door is called a trolley. You can see it hanging from the drum. The rope attaches to the trolley, and it automatically swings the door into the chain around the main motor of the garage door opener. If you can freely move your garage door by your hand, the trolly might be in bypass mode. Pull the rope towards the door to take the trolley latch out of bypass mode. As soon as you activate the garage door opener, the trolley will latch back onto the chain and work appropriately.
Remote batteries can also function as the reason for problems with the doors not closing correctly. Garage doors require electric energy from each side, in particular from remote controls and also from the entrance door operator, to operate correctly. If actually remote doesn’t work, then it signifies that your remote batteries have perished.
If your garage door doesn’t close all the way but will shut off without retracting, use the limit screws to adjust their length. These screws have contacts that tell the garage door opener how far to open or close, and it basically takes a few minutes to adjust them.
Open the flap on your garage ceiling or pull out your garage door opener’s light cover. You’ll see two plastic adjustment screws named Up and Down. Using a flat screwdriver, turn Down the screw in quarter-turn increments, checking how your garage door opens and closes when you make adjustments. Adjust it until the garage door closes all the way and compresses the rubber seal slightly. If the door closes and bounces the door back to open, set back the down adjustment off.
If the door troubleshooting technique isn’t working, you may need to call a technician. While you wait, put your vehicle into a park by tugging on the bypass rope. Your door attaches to the trolley system, so while you press the button, you should be able to close your door. If your door does not have integrated locking latches, your tracks will have small holes that you’ll be able to feed a bolt through that will effectively close the door.
If your garage door fails to open and there there’s a flashing light, your garage door opener is trying to clue you in as to what the problem is. Count the number of times the light blinks and look at your owner’s manual’s troubleshooting guide. If you do not have your manual, you can probably look up the problem code online. Simply locate a door opening device by running the title through by manufacturer and model number, and look for trouble code info.
If the remote battery dies, it can be a reason why the garage door must be opened. But when remote batteries are working properly, there might be an obstacle between the remote and the opener. Additionally, if you’re out of range to open the garage door from the remote, there may be an issue with the remote antenna. Sometimes broken remote antenna can also cause these problems.
In conclusion, if your garage door is not closing, it could be due to a variety of reasons. It could be that the sensors are dirty or misaligned, the tracks are bent or obstructed, or the springs are broken. If you have checked all of these things and your garage door still won’t close, it’s time to call a professional. You can call us for any garage door service at +1 (780) 616-6294. We are 24/7 available for emergency repair service.
Your email address will not be published. Required fields are marked *
Comment *
Name *
Email *
Website
Save my name, email, and website in this browser for the next time I comment.
Post Comment
